Hi, I've been trying to match my Siege sens to Cod, and somehow it feels very low.

I can do a complete 180 across my mouse pad in siege but in cod I can do less than 90

I am attaching my settings below can someone help me out?

 

Thanks

 

I can't see your settings from your screenshot, but it seems like you haven't set the Normal match to 360 distance. Your 360 distance in R6 is 20.8 inches while it's 29.4 inches in MW.

1 hour ago, FearlessCoppeR said:

Hi, I've been trying to match my Siege sens to Cod, and somehow it feels very low.

I can do a complete 180 across my mouse pad in siege but in cod I can do less than 90

I am attaching my settings below can someone help me out?

 

Thanks

 

you also matched your siege ads to hipfire in cod

11 minutes ago, fortunate reee said:

you also matched your siege ads to hipfire in cod

Bingo! Didn't see that at first.

Here's how you would set up the calculator to convert the settings from ADS to low and ACOG to high (replace DPI and resolution with your own):

Noted. Thanks for your help.

Can someone help me to convert my siege to COD?

DPI: 2000
Res: 3440x1440
Monitor: 32 inch
FOV: 90
Horizontal Sens: 9
Vertical Sens: 9
ADS Sens: 70 (where can i put this value?)

Thanks alot

4 minutes ago, nummerxv said:

Can someone help me to convert my siege to COD?

DPI: 2000
Res: 3440x1440
Monitor: 32 inch
FOV: 90
Horizontal Sens: 9
Vertical Sens: 9
ADS Sens: 70 (where can i put this value?)

Thanks alot

Unless you convert directly from ADS, the ADS sens will be calculated based on the setup and should match your settings. If you set it up like this (pay attention to the ADS and Scope setup) both ADS and ACOG matches your siege settings, and will be converted to the low and high zoom sens for MW.

thanks for you help. But i get some errors on the output. What can i do?

2 minutes ago, nummerxv said:

thanks for you help. But i get some errors on the output. What can i do?

You need to use the settings from my screenshot. ADS and scope settings, location, FOV for MW etc. 

vor 21 Minuten schrieb DPI Wizard:

You need to use the settings from my screenshot. ADS and scope settings, location, FOV for MW etc. 

thanks .. that worked 😃 What does all that numbers mean? How do i know what to select on the next games for ADS, Scope and Normal?

And i got this value where the max 2.00 is:

 

Monitor Distance Coefficient 2.22

 

Edited March 16, 20206 yr by nummerxv

10 hours ago, nummerxv said:

thanks .. that worked 😃 What does all that numbers mean? How do i know what to select on the next games for ADS, Scope and Normal?

And i got this value where the max 2.00 is:

 

Monitor Distance Coefficient 2.22

 

Set the value to 2 in calculator and see the output for the re-calculated sensitivity numbers. As for what the numbers mean, the instructions will answer most of your questions.

As for other games, keep the setup and input game (Siege) as it is and just select a new game for the output.

Siege - 

H/V - 10/10

ADS - 81

DPI - 400 

FOV - 80 

Monitor - 24" 

i used the ADS method, I cannot enter 75% for Hipfire. Is this calculation correct? 

So my Warzone sensitivity is 8.6812, is this correct?

Edited March 25, 20206 yr by Kable

46 minutes ago, BuckForPuck said:

if you want I could calculate you the most precise value available for some skins in csgo

 

@DPI Wizard might want to yeet him

 

 

Edited March 25, 20206 yr by fortunate reee

1 minute ago, fortunate reee said:

@DPI Wizard might want to yeet him

👍

5 hours ago, Kable said:

Siege - 

H/V - 10/10

ADS - 81

DPI - 400 

FOV - 80 

Monitor - 24" 

i used the ADS method, I cannot enter 75% for Hipfire. Is this calculation correct? 

So my Warzone sensitivity is 8.6812, is this correct?

You need to adjust the ADS and Scope setup so the calculations for R6 shows your ADS sensitivity (81). You can either adjust both of them so both both ADS and ACOG shows 81, or if you want your ADS sensitivity converted to everything in MW, adjust ADS until the output shows 81, then set Scope to the same. Or opposite if you want ACOG converted to everything.

On 3/25/2020 at 3:32 PM, DPI Wizard said:

You need to adjust the ADS and Scope setup so the calculations for R6 shows your ADS sensitivity (81). You can either adjust both of them so both both ADS and ACOG shows 81, or if you want your ADS sensitivity converted to everything in MW, adjust ADS until the output shows 81, then set Scope to the same. Or opposite if you want ACOG converted to everything.

 

So i followed your screen shot wizard, I don't have the normal setting but everything else is similar 

 

so my ads sensitivity for Horizontal and vertical in warzone is 1.77? I'm a newbie to this and i'm confused. Please advise me if its correct.

I've been having some trouble converting my cod warzone hipfire sens to my R6S sens:

For the record my cod sens is 4.20 on 800dpi with relative 1.0x ads sense

My 360 distances aren't matching up

Edited April 15, 20205 yr by Eyepatch192

26 minutes ago, Eyepatch192 said:

My 360 distances aren't matching up

Try to select MDV then 360 distance again for Hipfire. If still an issue, can you please share the conversion?

1 minute ago, DPI Wizard said:

Try to select MDV then 360 distance again for Hipfire. If still an issue, can you please share the conversion?

Im good now, its just that idk how to put this into MW

Just now, Eyepatch192 said:

Im good now, its just that idk how to put this into MW

Select in-game instead of config file under location. You should also set sensitivity 2 in MW to 0 so it scales all the aims accordingly.

Just now, DPI Wizard said:

Select in-game instead of config file under location. You should also set sensitivity 2 in MW to 0 so it scales all the aims accordingly.

ok will do and then update you

Is this right?

Just now, Eyepatch192 said:

Is this right?

Yes.

Just now, DPI Wizard said:

Yes.

Thank you man, it means alot from me to get help from you so quickly.