Apex Legends

[DPI Wizard]

Apex Legends

[Its_My_Purpose]

Settings to convert PubG 45 sensitivity to Apex?

[TheNoobPolice]

@DPI Wizard You can actually enter two decimal places in the sens box by double clicking and typing in-game, so can get slightly better discrepancy than the calculator currently shows I think?

Might be worth checking...

 

[DPI Wizard]

4 minutes ago, TheNoobPolice said:

@DPI Wizard You can actually enter two decimal places in the sens box by double clicking and typing in-game, so can get slightly better discrepancy than the calculator currently shows I think?

Updated!

[Pyroxia]

Thanks @DPI Wizard is it possible to add config file settings?

[noaimBoii]

How does the ADS sensitivity match between scopes with different FOVs?

[DPI Wizard]

8 minutes ago, noaimBoii said:

How does the ADS sensitivity match between scopes with different FOVs?

MDV 0% most likely, only tested ADS so far though.

[Wineku]

If anyone would be kind enough to convert Killing Floor 0.75 sens / 800 dpi into this game...

[Rossicle]

by the look of it if you match fov, hipfire is the same as cs:go

[FlynnB2]

Config files are located here: C:\Users\...\Saved Games\Respawn\Apex\local\settings.cfg

[Contrololol]

So just to clarify as this is the first time i've had a read through the forums: If i'm using 74 FOV in game in BFV, I should set it to 74 in Apex too? (as both using 4:3 Hdeg)

[stereo3D]

check the fov value for GstRender.FieldOfViewVertical in the config and use that in the calculator.

[Contrololol]

1 minute ago, stereo3D said:

check the fov value for GstRender.FieldOfViewVertical in the config and use that in the calculator.

Yeah 74 is what is in the PROFSAVE_profile file

[stereo3D]

ok, that's vertical fov though, so you need fov 90 in source engine.

[Contrololol]

So 90 ingame is correct then?

Edited February 5, 2019 by Contrololol

[stereo3D]

yes.

[Contrololol]

Thanks heaps

[ClanZes]

someone can corvert 43.5005 Hip fire ands ADS MDV 0%

[DPI Wizard]

1 hour ago, Tripl3_Sev7n said:

Config files are located here: C:\Users\...\Saved Games\Respawn\Apex\local\settings.cfg

Config file sensitivity is added.

[Carlos Resurreccion]

11 hours ago, DPI Wizard said:

MDV 0% most likely, only tested ADS so far though.

Hey @DPI Wizardhow do ADS scopes from 1-8x scale? I'm asking because I'm only used to Battlefield V USA scaling (1.777 coefficient because 21:9), and I'm spot on with any scope in Battlefield.

Scopes here feel weird. Up to what zoom can I use to stay true to Battlefield sens? (I'm using the same sens ingame as in Battlefield as per your calculator)

[DPI Wizard]

Just now, Carlos Resurreccion said:

Hey @DPI Wizardhow do ADS scopes from 1-8x scale? I'm asking because I'm only used to Battlefield V USA scaling (1.777 coefficient because 21:9), and I'm spot on with any scope in Battlefield.

Scopes here feel weird. Up to what zoom can I use to stay true to Battlefield sens? (I'm using the same sens ingame as in Battlefield as per your calculator)

Working on this right now, will update when done!

[Howling]

if i want the same fov as 90 fov in call of duty (1920*1080) How much fov should I set in APEX ?

[stereo3D]

@DPI Wizardrestarting the game changes the sliders back to 1 decimal place, but in the config it still shows 2 decimal places, so it might actually support 6 decimal places through the config like tf2.

also there is a profile.cfg with cl_fovScale.

i'm wondering how accurate the fov slider is because 90 / 70 = 1.2857 but in the conifg it says cl_fovScale "1.28679"

Edited February 5, 2019 by stereo3D

[DPI Wizard]

2 hours ago, stereo3D said:

@DPI Wizardrestarting the game changes the sliders back to 1 decimal place, but in the config it still shows 2 decimal places, so it might actually support 6 decimal places through the config like tf2.

Config file is added, which supports at least 6 decimals.

Also updated with holo, 6x and 10x.

2 hours ago, stereo3D said:

also there is a profile.cfg with cl_fovScale.

i'm wondering how accurate the fov slider is because 90 / 70 = 1.2857 but in the conifg it says cl_fovScale "1.28679"

It is a bit inaccurate, which is why scope calculations will be off by a few counts.

[ProuDBeasT]

Is there a way to change the sensitivity for any scope (holo, 6x or 10x for now) without changing the ADS sensitivity?

Maybe using the other sensitivity scalars?